ACS350 MANUAL PDFMay 22, 2020
View and Download ABB ACS user manual online. ACS Inverter pdf manual download. MTAC pulse encoder interface module user’s manual 3AFE MUL1- R1 installation instructions for ACS, ACS,. ACS, ACS and. ACS Drives Users Manual ACS Three Phase Input. ABB ACS general machinery drives are designed for the OEM machine building sector.
|Published (Last):||8 February 2008|
|PDF File Size:||17.22 Mb|
|ePub File Size:||17.10 Mb|
|Price:||Free* [*Free Regsitration Required]|
Download pdf ABB Acs yang lengkap xcs350. Enter the motor data from the motor nameplate: Fasten clamping plates See Figure a below. DI4,5 See selection DI1,2.
FlashDrop is an optional device for fast copying of parameters to unpowered drives. Operation Operation You operate the control panel with the help of menus and keys. Two units with the same address are not allowed on-line. Drive is programmed for traverse control with 30 sequences.
ABB ACS USER MANUAL Pdf Download.
Parameter mode In the Parameter mode, you can: Set also deceleration time 2 parameter if two deceleration times will be used in the application. System overview The drive can be connected to an external control system via a fieldbus adapter or embedded fieldbus. Initially, the panel is in the Output mode, where you can Fieldbus network Fieldbus adapter Drive Industry standard drive profile e. Follow the instructions in chapter Safety on page 5. Speed Control Fieldbus interface as the source for forcing ramp input to zero, i.
Reference Mode Reference mode In the Reference mode, you can: Page 47 Select the application macro parameter Operation And Start-up Operation and start-up These warnings are intended for all who plan the operation, start up or operate the drive.
Field Alternatives Significance Control location Majual control is local, that is, from the control panel. How to start, stop and switch between local and remote control You can start, stop and switch between local and remote control in any mode. Read only copy of the Fieldbus Control Word. Operation time scheme The time scheme below illustrates the operation of the brake control function.
Parameter Backup Mode Parameter Backup mode The Parameter Backup mode is used to export parameters from one drive to another or to make a backup of the drive parameters. With Pt the output current is 9. Thermal overload protection of the motor According to regulations, the motor must be protected against thermal overload and the current must be switched off when overload is detected.
Constant speed activation overrides the external speed reference. External Fault External Faults 1 and 2 can be supervised by defining one digital input as a source for an external fault indication signal.
If ignored, physical injury or death may follow, or damage may occur to the drive, motor or driven equipment. State 1 is active for 40 s. Wire Macro 3-wire macro This ac350 is used when the drive is controlled using momentary push-buttons. User Parameter Set 1 is loaded into use.
See section Speed compensated stop on page Replacement fans are available from ABB. It is also acd350 to activate jogging function 1 or 2 through fieldbus. Contact your local ABB representative for the approved breaker types and supply network characteristics.
The safety instructions given in chapter Safety must be followed during the start-up Selecting The Power Cables Selecting the power cables General rules Dimension the input power and motor cables according to local regulations.
This selection will be added later. A new parameter value of a standard macro is saved automatically when changed from the panel but not when altered through a fieldbus connection.
ABB ACS350 User Manual
Do not use other than ABB specified spare parts. Direction through digital input DI4. The full set, partial parameter set application and user sets can then be downloaded from the control panel to another drive or the same drive. Speed control performance figures The table below shows typical performance figures for speed control.
Assistant panel Basic panel Falling edge of inverted digital input DI1: Flux Optimisation Flux Optimisation reduces the total energy consumption and motor noise level when the drive operates below the nominal load.
Page Technical data What this chapter contains The chapter contains the technical specifications of the drive, e. The installation must always be designed and made according to applicable local laws and regulations. Time and Date mode In the Time and Date mode, you can: Symbols Input continuous rms input current for dimensioning cables and fuses Output continuous rms current.
Frequency input Digital input DI5 can be programmed as a frequency input.
Select the motor control mode parameter Example The time scheme below visualises the operation of the sleep function. A positive or zero minimum manula value defines two ranges, one positive and one negative. Cooling Air Flow Requirements all digital inputs in the on state and the panel, fieldbus and fan in use.